Mercury AirDeck 899194001 Especificações

iAll of us at Mercury Marine want to thank you for choosing aMercury Marine Inflatable boat. You have made a soundinvestment in boating pleasu

GENERAL INFORMATION6Boater's ResponsibilitiesThe operator (driver) is responsible for the correct and safeoperation of the boat and

GENERAL INFORMATION7Lanyard Stop SwitchThe purpose of a lanyard stop switch is to turn off the engine whenthe operator moves far enough away from the

GENERAL INFORMATION8Important Safety Information: The purpose of a lanyard stop switchis to stop the engine when the operator moves far enough awayfro

GENERAL INFORMATION9! WARNINGAvoid serious injury or death from deceleration forces resultingfrom accidental or unintended stop switch activation. The

GENERAL INFORMATION10WHILE BOAT IS STATIONARY! WARNINGStop your engine immediately whenever anyone in the water isnear your boat. Serious injury to th

GENERAL INFORMATION11There is another less common hazardous result from allowing yourboat to launch off a wave or wake. If the bow of your boat pitche

GENERAL INFORMATION12• The boat could move suddenly in a new direction. Such asharp change in direction can cause occupants to be thrownout

GENERAL INFORMATION13! WARNINGAvoid the combination of a running engine and poor ventilation.Prolonged exposure to carbon monoxide in sufficient

GENERAL INFORMATION14WHILE BOAT IS MOVINGab21628a - Running the boat with the trim angle of the bow too highb - Running the boat with no forward hatch

GENERAL INFORMATION15Never be under the influence of alcohol or drugs while boating (itis the law). Alcohol or drug use impairs your judgment and grea

iiRecord your Hull Identification Number (HIN) and engine model/serial number. The HIN is located on the back of the boat on thestarboard side. The en

GENERAL INFORMATION16DescriptionModel240 270 310 340Gross weight ‑Hypalon fabric‑43.1 kg (95 lbs.)45.7 kg (101 lbs.)48.7 kg (107 lbs.)Maximum load480

GENERAL INFORMATION17Manufacturer's PlateThe manufacturer's plate is located on the inside of the boattransom.abcdefghi14598a - Bo

GENERAL INFORMATION18Boat Design Categories Navigation Wind Force and Wave HeightC InshoreDesigned for voyages in coastalwaters, large bays, estuaries

BOAT COMPONENTS19Components LocationBACK VIEWa24737a - Hull identification number (HIN)FRONT VIEWab24738a - Lifting handle b - Towing rings

BOAT COMPONENTS20TRANSOM VIEWabccdef24739a - Air deck floorb - Air deck air chambervalvec - Towing holesd - Motor platee - Manufacturer's platef

BOAT COMPONENTS21SIDE VIEWbacdegf24740a - Tie down ringsb - Port air chamber valvec - Front air chamber valved - Overpressure valve onhypalon models o

TRANSPORTING22Trailering BoatUse a trailer that will properly support the boat hull. Position theboat on the trailer so it will rest in a stable posit

OPERATION23Inflating! CAUTIONDo not use a compressed air source to fill air chambers. Overinflation may result in damaged seams and/or bulkheads.IMPOR

OPERATION24f. Starting at one of the air valves, inflate each air chamberin turn, inflating only a quarter of the way full. Repeat thisprocedure to

OPERATION25NOTE: Keep items clear of the overpressure valve that couldprevent the red cap from popping off the valve.a24745a - Red capDrain V

TABLE OF CONTENTSiiiWARRANTY INFORMATIONTransfer of Warranty...1Warranty Registration

OPERATION26SLIDE DRAIN VALVE OPERATIONWhen underway, slide the drain to the open position and the waterwill automatically run out. The inner diaphragn

OPERATION27• Be sure there is an approved personal flotation device ofsuitable size for each person aboard and readily accessible (itis the l

OPERATION28TowingIf the inflatable boat is to be towed by another boat, the inflatableboat must be empty. Remove outboard, fuel tank, and equipment.At

MAINTENANCE29Cleaning ProcedureFABRIC SURFACESInflate the air chambers. Clean the fabric with a mild soap and freshwater solution. Rinse with fresh wa

MAINTENANCE303. Push in the valve stem and deflate the floor. Push in the valvestem and turn the stem a quarter turn clockwise to lock thevalve in the

REPAIRS31General InformationSmall repairs may be attempted by the owner if the repairinstructions are followed. Tears or holes larger than o

REPAIRS32The repair kit which comes with the boat is a one part glueoperation and should be used for emergency minor repair. For apermanen

REPAIRS33Apply two thin layers of adhesive using a short bristle brush, in acircular pattern on both the backside of the patch and the patcharea on

REPAIRS34For the best results when gluing, the relative humidity should beless than 60%, ambient air temperature should be between18 °C to 25

STORAGE35Storage PreparationNOTE: The boat should be cleaned and rinsed with fresh waterbefore being placed in long term storage. Refer to the Cleanin

TABLE OF CONTENTSivTowing...28Air Chamber Deflates Accidently...

OWNERS SERVICE ASSISTANCE36Service AssistanceYour satisfaction with your inflatable product is very important toyour dealer and to us. If you ev

WARRANTY INFORMATION1Transfer of WarrantyThe limited warranty is transferable to a subsequent purchaser, butonly for the remainder of the unused porti

WARRANTY INFORMATION2Mercury MarineAttn: Warranty Registration DepartmentW6250 W. Pioneer RoadP.O. Box 1939Fond du Lac, WI 54936-1939920-929-5054Fax 9

WARRANTY INFORMATION3DURATION OF COVERAGEThe fiberglass hull, air deck® floor, all hull attachments andaccessories, but not limited to, floor

WARRANTY INFORMATION4HOW TO OBTAIN WARRANTY COVERAGEThe customer must provide Mercury with a reasonable opportunityto repair, and reasonable acces

WARRANTY INFORMATION5DISCLAIMERS AND LIMITATIONS:THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE ARE EXPRESSLY DISCLAIME