Mercury PVCLE266M-L Especificações

This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved.

Package Contents Your motherboard package ships with the following items:  The motherboard  The User’s Manual  One diskette drive ribbon cable

Static Electricity Precautions Static electricity could damage components on this motherboard. Take the following precautions while unpacking this mo

Chapter 2 Motherboard Installation To install this motherboard in a system, please follow these instructions in this chapter:  Identify the mo

Motherboard Components Motherboard Components Use the diagram below to identify the major components on the motherboard. Use the diagram below to ide

PS/2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device. PS/2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard. LPT1 Use LPT

DIMM1 DIMM2 Installation Procedure These modules can be installed with up to 2 GB system memory. Refer to the following to install the memory

Jumper Settings Connecting two pins with a jumper cap is SHORT; removing a jumper cap from these pins, OPEN. 1 JBAT1 Jumper JBAT1: Clear CMOS

SYSTEM_FAN1 1ATX1 1PANEL1 Connect the power connector from the power supply to the ATX1 connector on the motherboard. If there is a cooling fa

SPK1: Speaker Connector Connect the cable from the PC speaker to the SPK1 header on the motherboard. Pin Signal Pin Signal 1 SPKR 2 NC 3 GND 4 +

Pin Signal Pin Signal 1 VCC 2 USB- 3 USB+ 4 GND 5 KEY The J5 is shared with one of the USB ports of the I/O back panel. The USB port is l

Notice: Owing to Microsoft’s certifying schedule is various to every supplier, we might have some drivers not certified yet by Microsoft. Therefore,

Install Other Devices Install and connect any other devices in the system following the steps below. 1FDC1IDE1IDE211 Floppy Disk Drive The mother

If you want to install more IDE devices, you can purchase a second IDE cable and connect one or two devices to the Secondary IDE channel connector ID

Expansion Slots This motherboard has one CNR and two 32-bit PCI slots. PCI1PCI2CNR1 Follow the steps below to install a CNR/PCI expansion card.

Chapter 3 BIOS Setup Utility Introduction The BIOS Setup Utility records settings and information of your computer, such as date and time, the type

Running the Setup Utility Every time you start your computer, a message appears on the screen before the operating system loading that prompts you t

Standard CMOS Setup Page Use this page to set basic information such as the date, the time, the IDE devices, and the diskette drives. If you press th

Advanced Setup Page Use this page to set more advanced information about your system. Take some care with this page. Making changes can affect the o

BootUp Num-Lock This item determines if the Num Lock key is active or inactive at system start-up time. Floppy Drive Swap If you have two diskette dr

AGP Aperture Size This option determines the effective size of the AGP Graphic Aperture, where memory-mapped graphic data structures are located. Au

Suspend Time Out This item sets up the timeout (minutes) for the Suspend mode. The computer will be a power-saving Suspend mode if the system has b

Table of Contents Trademarks... I Chapter 1: Introduction...

PCI / Plug and Play Setup Page This page sets some of the parameters for devices installed on the PCI bus and devices that use the system plug and p

Load Optimal Settings If you select this item and press Enter a dialog box appears. If you press Y, and then Enter, the Setup Utility loads a set of

OnBoard IR Port This item enables or disables the Infrared port, and assigns a port address. If you select a specific address, the resources are ass

CPU PnP Setup Page This page lets you manually configure the motherboard for the CPU. The system will automatically detect the kind of CPU that you h

Hardware Monitor Page This page sets some of the parameters for the hardware monitoring function of this motherboard. AMIBIOS SETUP – HARDWARE MONI

Change or Remove the Password Highlight this item, press Enter and type in the current password. At the next dialog box, type in the new password, or

Chapter 4 Software & Applications Introduction This chapter describes the contents of the support CD-ROM that comes with the motherboard packag

Installing Support Software 1.Insert the support CD-ROM disc in the CD-ROM drive. 2.When you insert the CD-ROM disc in the system CD-ROM drive,

Auto-Installing under Windows 98/ME/2000/XP If you are under Windows 98/ME/2000/XP, please click the Setup button to run the software auto-installin

Installing under Windows NT or Manual Installation If you are under Windows NT, the auto-installing program doesn’t work out; or you have to do the

IV

Chapter 1 Introduction This motherboard has a VIA C3 CPU onboard with front-side bus speed up to 133MHz. This motherboard integrates the VIA CLE266

Key Features The key features of this motherboard include: CPU Type ♦ Supports the VIA C3 CPU onboard ♦ Supports 133 MHz Front-Side Bus Chipset

Onboard IDE channels ♦ Primary and Secondary PCI IDE channels ♦ Support for PIO (programmable input/output) modes ♦ Support for Multiword DMA mode

Onboard I/O Ports The motherboard has a full set of I/O ports and connectors: ♦ Two PS/2 ports for mouse and keyboard ♦ One serial port ♦ One VGA

BIOS Firmware This motherboard uses AMI BIOS that enables users to configure many system features including the following: ♦ Hard drives, diskette d